Realacc / Matek HUBOSD ECO H Type w/STOSD8 Current Sensor 5V 12V Dual BEC PDB


This product is not available anymore. May be you can find similiar products in the same category (please, follow the link above).

We do not remove such products from the catalogue because customer reviews on them may contain useful information.
Realacc / Matek HUBOSD ECO H Type w/STOSD8 Current Sensor 5V 12V Dual BEC PDB

Realacc HUBOSD ECO H Type w/STOSD8 Current Sensor & Dual 5V 12V BEC PDB

























The HUBOSD eco has been engineered to provide the highest possible performance and reliability in a 46*36mm & 4 layers PCB.
It is a multifunctional HUB with PDB, BEC 5V/2A &12V/500mA, Current sensor 140A, STOSD8. It is specially made for the mini FPV Quad.
The BEC 12V is linear regulator, no LC Filter needed. Built-in STOSD8 can support Plug & Play, no complicated settings needed.

Specification:
Brand name: Realacc
nput voltage range (3S-5S operation): 8 - 21VDC
PDB: 4x30A (Max.4x35A)
Regulated 5V and 12V outputs
Current Sensor 140A
Built-in STOSD8
Physical:
- 2oz copper, 4-layers &1.6mm PCB.
- 1x Battery input, 4x ESC outputs.  2x BEC 5V outputs, 2x BEC 12V outputs.
- Camera signal & Gnd pads, Video Transmitter Signal & Gnd pads
- 1x Serial port (RX, TX, G)
- Dimensions: 46x36x4mm, Weight: 8.5g
- Mounting holes 30.5mm square spacing

PDB (ESC outputs)
Continuous current: 30A per output
Peak current (10 seconds/minute): 35A per output

BEC 5V outputs
Designed for RC Receivers, Flight controllers, OSD, and Servos.
DC/DC synchronous buck regulator.
Voltage: 5.0 +/- 0.1VDC
Continuous current: 2 Amps (Max.2.5A 10s/minute)
Output Ripple: 40mV (VIn=16V, VOut=5V@2A load)
Short-circuit tolerant (5 seconds/minute)

BEC 12V outputs
Linear regulator, very low noise. LC Filter is needless.
Designed for Video TX or FPV camera.
Voltage: 12.0 +/- 0.3VDC (4~5S operation)
Continuous current: 500mA@16V IN,  400mA@20V IN
Short-circuit tolerant (2 seconds/minute)
If the battery is 3S LiPo,  Output voltage=3S LiPo voltage - 1V

Current Sensor
140A
If current >140A. STOSD display 140A

STOSD8

Running indicator

Blue LED blinks: STOSD is initializing
Blue LED light: STOSD is working.

Autodetect PAL/NTSC
Auto sense PAL / NTSC cam at OSD startup. Default is NTSC without Cam signal

Dynamic on screen info
Current < 2A & keep 5 seconds                     Current > 2A




Min.Volt & Max.Amp recorder

Automatic flight timer
Current > 2A, Time in.  Current < 2A,Time out..

Auto battery cells detection
If the Input voltage is in the range of following, The HUBOSD will detect the cell
numbers automatically.
11.1~13.05V: 3cells LiPo,  14.8~17.4V: 4cells LiPo,  18.5~21V: 5cells LiPo
If the input voltage is out of the range. The voltage value will blink on screen.
Pls check if the battery total voltage is below 3.7V*cells

Low vlotage alarm
 (Value blinks): Default 3.6V* cells

Exceeding mAh alarm
 (Value blinks): Default 1000mAh

Onscreen Pilot ID
Default is disable. you can type some words & enable it in GUI

Firmware upgradable
Voltage precision: +/- 0.4%, Voltage resolution: 0.01V
Current precision: +/- 1.5%, Current resolution: 0.1A

User Manual, Click here.

Package Included:
1 X BEC board


close
Comments
Post review

Feedback
/ Register
Your country:
Follow a few simple steps to place an order. Mouse over a picture for details.
Deleted items